Cano tile   Carrie bathroom   Deller Head
Damping buffer cover:
Unlike ordinary seat covers, this kind of cover plate with damping function can prevent the jarring noise from being emitted when the cover plate and the toilet ring are closed. Instead, the damping cover plate is lowered by using the principle of frictional resistance. When closed, the speed can be slowed down without any noise.
Flange ring:
Flange ring is the seal ring, in fact, many industrial bearings between the shock absorption and wear rubber rubber pad called flange, toilet flange is placed on the toilet between the sewage outlet and bathroom water hole, To the effect of the seal, the siphonic toilet does not leak, flushing effect is better.
Water seal:
Toilet water in the pool surface. Prevents odor spills or small insects crawling out of the drain pipe.
Lip surface:
An annular diarrhoea circle under the toilet is similar to a toilet seat and can be generally classified into two types: CloseRim and OpenRim. The closed lip has a uniform hole at its lower edge. The lower lip of the open lip is an open type and is a conduit for the water in the tank to be drained and washed.
Pit distance:
Usually we say the pit distance refers to the vertical distance from the wall to the center point of the toilet sewage outlet, generally divided into 300mm and 400mm pit distance, there are special pit distance, so be sure to first measure the size and then go to buy the toilet .
waterway:
Toilet bowl front and rear sewage pipes.
Water cover:
In the surface of the toilet bowl, the wider the surface of the bowl is, the less likely it is to contaminate the soil.
Flush type:
Falling water from the surface of toilet bowl flushed with water level.
Siphon type:
SiphonWashCloset SiphonWash is a siphon that is formed by flushing water in the toilet's sewer pipe (usually called a trap) and drains the dirt. The structural feature of the siphonic toilet is a complete tube inside the toilet. The shape is laterally inverted and “S†shaped. The difference in water level when using water supply promotes the formation of siphonage. Since water is not used to wash away the dirt, the slope of the pool wall is relatively gentle, and the bottom of the pool also expands the water storage area. This solves the problem. Drawback noise is too large.
Falling
(BlowoutWaterCloset) Use a strong water flow (usually a "1" inlet pipe) to flush the dirt out of the surface of the toilet bowl. Slurry can be quickly washed out in the flushing moment, the cleaning effect is good, and the pipeline is not easy to block. The flush type uses the momentum of the water stream to discharge the dirt. In order to increase the hydraulic force that drops from the water separation hole around the toilet bowl, the wall of the pool is usually designed to be steeper, and in order to make the water concentration, the pool of water is designed with a smaller area. The disadvantage of this type of flushing is that it The water noise is large, and at the same time, due to the small area of ​​water seal, it is easy to produce scale.
Jet siphon:
Siphon-jet WaterCloset This is an improved type of siphon-type toilet. Its structural feature is the addition of an additional spray channel on the basis of the siphon type toilet. The injection port is aligned with the center of the sewage pipe inlet. The caliber is usually 20 mm.
When the water supplied by the water tank passes through the water circle, part of the water from the water separation hole flows out of the wall of the cleaning tank and falls into the pool, and part of the water flows out from the injection port through the injection auxiliary passage. Its role is to use its large current of water to discharge dirt into the sewage pipeline. At the same time, its large-diameter water flow speeds up the discharge of sewage pipes to accelerate the formation of siphonage. Since the jet flow is carried out underwater, it does not increase noise, but noise problems are also improved. This product is designed. , consciously expanded the water storage area, limit the depth of water retention, because of deodorant, anti-splash effect.
Siphon type:
The siphon that is flushed out of the drainage channel with the flushing water will drain the toilet bowl. When flushing, the flushing water will fill the sewage draining channel, and the water and dirt in the toilet bowl will be pumped out after forming the siphon. The function of the sewage discharge depends on the structure of the pipeline, the height of the water seal, and the size and direction of the flushing force. The feature is that the flushing noise is less than that of a flush toilet.
Whirlpool Siphon:
Deodorant, good anti-fouling effect, less noise (Siphon-VortexCloset) uses flushing water to spray from the side of the bottom hole of the pool to form a vortex, with the increase of the water level filled with sewage pipes, when the water level in the toilet and the toilet sewage outlet form a water level When it is bad, the siphon is formed and the dirt is discharged. Its structure is basically similar to that of other siphons. Only the water supply pipe is arranged at the bottom of the bowl and leads to the bottom of the pool. The greatest advantage of this type of toilet is the use of vortex and siphon. The vortex creates a strong centripetal force on the water surface around it, causing the liquid and dirt on the surface to quickly get entangled in the vortex, which is discharged as the siphon is generated. Therefore, the sewerage process is quick and thorough, with deodorant and better antifouling effect. The characteristics of less noise.
Water-saving toilet:
According to the mandatory regulations issued by the Ministry of Construction, the stool flushing water consumption should not exceed 6 liters per wash cycle, when the water pressure is 0.3 MPa, the flushing volume should be 6 liters per litre, and the urine flushing product should be flushed once. A flush volume of 2 to 4 liters (if two-stage flushing is used for each of the first and second paragraphs). Rinse time is 3 seconds to 10 seconds
Bidet:
As the name implies, this kind of sanitary ware is used to clean the lower part of the human body. Some manufacturers call it "female wash basin". In fact, it can be used by both men and women. It is especially useful for people who need to soak liquid medicine.
Skirt:
The "skirt" in the general bathroom refers to the rim of the bathtub around the bathtub. Generally, the bathtub with the skirt can be installed independently. If not, the tiles are installed around the bathtub to support the rim.
Shower screen:
The shower screen is generally located in the shower area of ​​the bathroom. The model is divided into two types: hanging on the wall and directly on the ground. There are various showers, massage jets and connecting pipes on the top, and some even have other functional configurations such as radio. Allows you to enjoy comfortable showers for homes where you don't want to have a bathtub or a bathroom with a limited area.
Yuba:
Yuba is a device installed in the bathroom roof for heating, also known as multi-functional bathroom heater, the main source of heat is infrared heating lamps, PTC, nickel-chromium wire, Yuba in addition to heating function, both ventilation, hair, Negative ions, lighting and other functions.
Shower:
Shower head
Integrated integrated ceiling:
The modern one-piece integrated ceiling is integrated with heating, ventilation, lighting, metal ceiling four functions, namely heating, ventilation, lighting installation of kitchen and bathroom, and metal ceiling installation in one step, all completed by modern manufacturers. The integrated ceiling has the largest limit to meet the family's personalized needs for kitchen and bathroom renovation.
>>> When the country meets IKEA Happy house slave sun 55 flat small apartment decoration
Sanitary Building Materials Knowledge Aisle Ceiling Lighting Toilet Household Decoration Bathroom Decoration Design Kitchen Ceiling Bathroom Design Toilet Ceiling Bathroom Tiles Bathroom Size Tile Glue ld Tile
Center Drill Bit is also known as Slocombe Drills, Centre Drills were originally designed to create the countersink required to locate a tailstock centre when turning between centres. They have a point angle of 60° to match the angle of a Tailstock Centre.
A Centre Drill can also be used to provide a start location for a drill when drilling down the centre of a bar held in a Lathe chuck. Centre Drills are short and rigid enough to mark the bar centre without wandering off if they are carefully offered up to a rotating work-piece.
Carbide Center Drills,Hardware Tool Step Drill Bit,Wooden Box Packed Drill,Hss Center Drill Set
Behappy Crafts (suzhou)Co.,Ltd , https://www.haoyuebehappy.com