When decorating the house, it is the decoration material, and the cassette in the decoration material is a small one, but it plays a big role in our house. The cassette is used inside the wall, even in the future. It’s hard to find problems when they grow up, so we have to worry about it when we choose. So how is the dark box broken? Many people don't know how to deal with it. Today, Xiaobian will come with everyone to see how the dark box is broken and the cassette installation precautions!
What if the cartridge is broken?
1, gadget name: cassette repair This kind of cassette repair is also relatively cheap, generally a few dollars, you can buy about 10 for 20 or 30 dollars.
2, first of all, we need to clean up inside the cartridge to ensure clean, and then use long screws in the support rod (mainly with the support bar) above the first spreader bar adjustment screw was loose a little, to facilitate put into Inside the cassette.
3. After putting in, adjust the position of the support rod and try to be close to the inside.
4. Then lift the long screw and use the micro-wrench to extend the screw of the support rod. The upper screw is turned counterclockwise, the lower screw is screwed clockwise, and then the entire support rod can be stably standing inside.
5. After tightening, make sure the support rod is stable, then you can remove the long screw.
6. After unloading, there is a place where the screw can be screwed. The support rod is installed, and then the cover panel of the socket can be installed.
7. There is a screw hole on the socket, then use the long screw to pass through the screw hole, find the screw on the support rod inside, and then tighten it.
Cartridge installation notes:
First, the waterway renovation of the kitchen waterway renovation mainly includes faucets and water heaters. The general family shares kitchens and toilets with one water heater. Therefore, when renovating the waterway, you must think about the location of the water heater installation, so as to determine the installation of the hot and cold water pipes. Location, waterway reconstruction. When installing the water heater, pay attention to the uniformity of the water outlet on the cold and hot water. The nozzle should be 2 cm above the wall and the distance between the hot and cold water pipes is 15 cm. This standard should be strictly enforced.
Second, the bathroom waterway renovation bathroom waterway transformation of more content, wash basin, toilet, bathtub and washing machine installation location, whether you need hot water pipe to achieve good, the drain of the sewer treatment should be in place, otherwise it will cause back water phenomenon .
Circuit modification is more than every room decoration, so it is more important to pay attention:
First, the circuit of the living room to transform the living room need to install the wire line including power line, lighting line, air conditioning line, TV line, telephone line, computer line, doorbell line and so on. The position of the wire needs to be considered in advance, and the reservation work should be done. Generally speaking, it is necessary to leave the telephone line at the edge of the sofa, and to leave the doorbell line at the inside of the door, and reserve power for the water dispenser, humidifier and other equipment. In general, at least 5 power cords should be left in the living room.
Air conditioners, DVD players, etc., which are in the standby state, are preferably equipped with a switch socket panel, so that they are turned off directly when not in use, and no power is wasted.
Second, the bedroom circuit transformation bedroom circuit transformation generally includes power lines, lighting lines, air conditioning lines, telephone lines and computer lines. The power cord is reserved above the bedside table, and the 5-hole patch panel is suitable for switching, which can reduce the trouble of the bedside lamp not switching.
Although the cassette is a small decoration material, it is a detail that is not easy to ignore when it is renovated. You can't neglect it. The above is what Xiaobian said today, the dark box is broken. How to do it and the installation of the cassette is finished here. If you want to know more information, please continue to pay attention to the decoration home.
More related wonderful reading:
How to install the socket cassette? Socket cassette wiring precautions
Switch cassette size type switch cassette size detailed
Based on many years of rich experience in slurry pump manufacturing and design, NAIPU can undertake OEM customization for the whole set of pump and various spare parts. The slurry pump spare parts can be made of various material according to customer`s requirement, Such as : Alloy 20, Hastelloy Alloy , A 61,ceramic and polyurethane and so on.
OEM Slurry Pump,OEM Slurry Pump Parts,OEM Impeller,OEM Volute,OEM Mission Pump,OEM Goulds Pump,OEM High Chrome Slurry Pump Parts
Shijiazhuang Naipu Pump Co., Ltd. , https://www.naipu-pump.com