The overall wardrobe production process is different from the general purchase of panel furniture. First, the designer will have a close contact with the user, understand the user's hobbies and their home style, and then go to the door to measure and design a reasonable overall wardrobe. What are the precautions for wardrobe installation ?
1. Use a cloth to make a good floor, first start the assembly from the wide side plate on one end of the wall, and lay the wide side plate flat on the ground (a distance of 700mm from the rear wall). First, place the filled three-in-one rubber plug plate flat on the cloth, check the hole spacing and the drawings, and install a three-in-one single link. Then the solid nails are fastened to the cork and fixed on the wide side plate. The big handle hole of the top plate faces upwards, and the rest of the solid layers are facing downwards. The big handle holes of the foot line are inwards (the middle solid layer is the same height as the L frame, ie, the bottom plate is solid to the solid layer. The inner space is 960mm, and the floor plate holes are used. Put the side plate and screw it with a cork. The cork needs to connect the solid layers on both sides. Install the double connecting rod on the second cabinet, note that the big handle on the double connecting rod can only be locked half, ie 90°. When the two solid layers are fixed with the side plates, tighten the big handle at the same time. Repeat the installation procedure for the second cabinet when installing the third cabinet.
2. Nail back plate. Lay the entire cabinet side on the well-being floor and flatten the side panels into the same plane. Use a ruler to measure the diagonal dimensions of the cabinet and adjust it to equal. Install the first back plate from the wide plate. Note that if there is a nail in the middle of the solid nail, first draw the centerline of the solid layer with a pencil, and then nail it. nail.
3. L-frame installation. Use the side plate of the L frame to form a parallel line on the corresponding side plate, and then move the center line of the three-in-one rubber grain by 9mm upwards. Use the top of the L frame to draw a parallel line on the corresponding bottom plate. Inward 9mm draws three colloidal centerlines. Open hole with 10mm drill bit, hole depth 10-20mm. Install a single rod. After the L frame is installed, nails are fixed on the back plate.
4, clean up the wardrobe installation debris, left and right stations, one person, the wardrobe slightly backward, forced to lift, move back to the desired position not to scratch the floor, wall.
5, 1) The three-in-one rubber particles such as a drawer hole;
2) Connect the 2 and 3 side plates to the pumping surface;
3) Connect the 4 and 2 and 3 side plates and plywood with the middle solid layer ¢ 3.5*40 screws;
4) Insert the back plate 5 into the 2 and 3 slots and fix it on the back plate 4 with small nails. Install the inline pull handle (the puller is required to have a square angle of 90°).
Install three sections of rails: rails against the drawers, flush with the floor of the drawers, and move the rails to fasten the mounting rails to the vertical eyes of the sub-rails (this is an adjustable position). The distance between the two drawer panels and the central position of the track eye is added with a gap of 2mm. The data measured by the parent rails is removed and the crosscut line is drawn on the side panel of the cabinet by a 90° square. The cross-line is the central eyeliner of the parent rail. . Drawer panel is in the column, so draw the vertical tangent line from the outer edge of the side panel of the cabinet body. The vertical line of the parent rail is flush with the center, the center eye is flush with the crosscut line, and the screw is installed on the horizontal eye of the busbar (adjustable position). After the drawer is installed, adjust the position using the adjustable position so that the drawer is even and the gap is even. Finally, install the fixing screws on the horizontal eyes of the sub-track and on the vertical eyes of the parent rail.
And so on to install the next one. In case of a full drawer, the same principle can be installed from bottom to top. The uppermost drawer can be fixed with a 90° angle. Prerequisites require that the drawing surface be flat and uniform. The drawer gap is 2mm.
Information about the wardrobe installation notes was introduced here for everyone. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible.
Closet wardrobe
Rain Shower Head with Handheld Shower Faucet Set Complete with High Pressure.Includes one-piece cartridge to simplify installation and maintenance.Our shower system provides free replacement parts in 5 years.
Thermostatic Shower Faucet,Bath Shower Set,Shower Set Heads,Hand Shower Set
HESHAN CAIZUN SANITRAYWARE CO.,LTD , https://www.caizunbathroom.com